Shore hardness is one useful rubber-sheet property, but it does not predict abrasion, tearing, impact behaviour or service life. This guide shows mining buyers how to compare hardness with wear mechanism, test method and supporting data.
Two mining rubber sheets can show a similar Shore hardness and still behave differently in service. Hardness describes resistance to indentation under a stated test method. It does not, by itself, measure abrasion loss, tear propagation, tensile strength, elongation, impact behaviour or service life.
The useful buying question is therefore not "Which sheet has the higher hardness?" It is "Which test data and construction details match the wear mechanism at this installation?"
Before comparing data sheets, define what is damaging the rubber. Sliding fines, sharp rock, repeated impact, trapped material, flexing, cutting at an edge and chemical or temperature exposure do not create the same failure mode.
Ask the site team to identify:
· material handled, particle size range and whether sharp edges are present;
· dry, wet, oily or chemically exposed service;
· sliding, rolling, impact, compression, flexing or mixed contact;
· material drop height, flow direction and approximate contact angle;
· the location of actual wear, tearing, cutting, cracking or debonding;
· current sheet thickness, fixing or bonding method and observed failure pattern;
· cleaning method, shutdown constraints and replacement objective.
Photos of the worn area, a simple sketch and the previous material data sheet are often more useful than one isolated hardness number.
Data point | What it describes | What it does not establish alone | What must accompany it |
Shore hardness | Resistance to indentation under the stated scale and method | Abrasion rate, tear resistance, impact life or overall quality | Scale, method, specimen condition, tolerance and test basis |
Abrasion result | Material loss or volume change in a defined laboratory test | Universal field life in every mining duty | Method, units, specimen, test conditions and comparison basis |
Tensile strength | Stress carried before break under the stated test | Resistance to a growing cut or repeated impact | Method, units, specimen direction and conditioning |
Elongation at break | Extension before break in the test specimen | Permanent set, tear strength or service flexibility by itself | Method, units, specimen and conditioning |
Tear strength | Resistance to tear initiation or propagation in a defined specimen | Sliding abrasion rate or bond performance | Test geometry, method, units and specimen direction |
Thickness | Supplied geometry and wear allowance | Compound quality, correct fixing or suitability | Tolerance, dimensions, installation clearance and joint plan |
Reinforcement or bonding layer | Product construction for a stated supply form | Compatibility with every adhesive, substrate or installation process | Layer identity, substrate, adhesive system and installation responsibility |
This table is a reading guide, not a specification. A number has commercial value only when the method, unit, specimen and application are known.
![]()
Hardness is one result from one type of test. Two sheets with similar hardness may use different rubber compounds, fillers, curing systems, reinforcement or backing construction. They may also be tested under different methods or specimen conditions.
The operating duty then decides which differences matter. A sheet that resists indentation may still tear after a cut starts. A material with a favourable abrasion result in one laboratory method may not perform the same way under sharp impact, trapped rock or poor fixing. A high elongation result does not automatically prove resistance to cutting, and a strong tensile result does not predict service life.
This is why GRAND RUBBER should review the wear mechanism before discussing one target hardness. The objective is not to dismiss hardness. It is to place hardness inside a complete comparison.
Do not rank quotations until the rows below are aligned. Blank or differently defined fields should remain open, rather than being treated as equal.
Comparison field | Supplier A | Supplier B | Buyer check |
Product identity and compound | Same product type and intended duty? | ||
Hardness | Same scale, method, tolerance and specimen condition? | ||
Abrasion | Same method and units? Lower or higher result interpreted correctly for that method? | ||
Tensile strength | Same method, units and test direction? | ||
Elongation at break | Same method and conditioning? | ||
Tear strength | Same specimen geometry, method and direction? | ||
Thickness and tolerance | Same nominal size and usable supplied dimensions? | ||
Construction | Plain sheet, reinforced sheet or bonding layer clearly identified? | ||
Supporting documents | Current TDS, test report or certificate tied to the quoted product? | ||
Supply scope | Sheet only, cut pieces, packing, bonding layer or installation clearly separated? |
If the methods or units differ, the values may not be directly comparable. Request clarification instead of converting them into an artificial ranking.
· Treating a harder sheet as automatically more wear resistant.
· Comparing abrasion figures without checking method and units.
· Using tensile or elongation as a substitute for tear data.
· Ignoring a visible cut, loose fixing or trapped material that may drive failure.
· Assuming a bonding layer defines the complete adhesive and installation system.
· Asking for a service-life guarantee from laboratory values alone.
· Accepting a generic certificate that is not tied to the quoted product identity.
For a focused review, send the following information:
· equipment and exact wear location;
· material handled and particle size;
· sliding, impact, cutting, compression or mixed duty;
· wet, dry, oily, chemical and temperature conditions;
· current material, thickness, dimensions and failure mode;
· fixing, clamping or bonding arrangement;
· required supply form, quantity, tolerance and packing;
· target documents and any mandatory test method or standard version;
· photos, drawing and available previous test data.
GRAND RUBBER can then confirm which product information is available for the quoted sheet and identify which points still require technical review. Product-specific values, standards, tolerances and performance claims must be tied to an approved current TDS or test source before publication or order confirmation.
No. Higher hardness only means greater resistance to indentation under the stated test. The correct choice depends on abrasion, impact, cutting, tearing, flexing, fixing and operating conditions.
No. Service life depends on the complete product, installation and duty. A hardness result alone cannot support a life prediction.
Only when the test method, units, specimen and conditions are aligned. Otherwise, ask each supplier to clarify the basis.
There is no universal second value. Start with the observed failure mechanism, then review the relevant abrasion, tear, tensile, elongation, construction and installation information.
Send the wear location, material handled, duty, environment, dimensions, current failure, fixing method, photos and required documents. This allows a product-specific review without turning one laboratory number into an unsupported promise.
Send the application details and current failure photos to info@grandrubbers.com. GRAND RUBBER will review the comparison basis and confirm which product-specific documents can support the quotation. Final product selection and publication remain subject to technical approval.
Inquiry Now